Xtreme Motorworks LLC

Engine and Drivetrain


We have some customp parts for your engine and drivetrain.

Quietline Solid Motor Mounts

$48 / set

    Solid motor mounts that go between the motor plates and frame. Grade 8 hardware and Nylock nuts.

High Flow Cone Air Cleaner

$48 / ea.

    High Flow Air Cleaner Kit for that "HOT ROD" look. Great for pullers and max air flow. UNPAINTED

3" Red Spectre Air Filter

$30 / ea.

    Spectre 3" Red air filter.

Brass PTO Buttons

Cub Cadet Narrow Frame Brass PTO Button

$15 / ea.

    Press in Brass PTO Buttons. Sold each.

PTO Clutch Puller

Cub Cadet PTO Clutch Puller

$48 / ea.

    Heres a handy tool to get the PTO's off them tough Kohler engines. Each puller uses the 5/16" holes in the puller to pull it off. Has a handle to hold it from rotating and a threaded point bolt that uses a 9/16" wrench to do the work. Clearance slots to clear the welds.

Cub Cadet 782D, 882 Hi Torque Starter

Cub Cadet 782D Starter High Torque

$118 / ea.

    Fits the 782D, 882 and others with the Kubota 3 cylinder diesel motor (D600) . Brand new.

3" Cone Air Filter Base

$22 / ea.

    Base and spacer for high flow air cleaner kit. Diameter of the base is 3" and will fit all clamp on 3" air cleaners. UNPAINTED

Open Air Cleaner Kit

$49 / kit

    Open element air cleaner kit. Bolts in place of the stock application, giving you that open element "HOT ROD" look. UNPAINTED

1 1/4" Muffler Flapper

$14 / ea.

    1 1/4" to 1 1/2" Exhaust Flapper - Clamp on.

Stainless Steel Exhaust Tip Flat Cut

Cub Cadet Muffler

 

$22.50 / ea.

    Stainless Steel Exhaust Tip for Diesels. This is just for the extended tip. Muffler or rest of tractor not included. Approx. 14" long.

Stainless Steel Exhaust Tip Angle Cut

Cub Cadet Muffler

$22.50 / ea.

    Stainless Steel Exhaust Tip for Diesels. This is just for the extended tip. Muffler or rest of tractor not included. Approx. 14" long.

Kohler Fuel Atomizer

$15.50 / ea.

    Turns the air/fuel flow into the valve chamber into a straighter, condensed streamlined flow. 1/4" stick steel. Gaskets or bolts not included. No Guarantees if it works or not! UNPAINTED

Kohler Carb Spacer

$11.50 / ea.

    Spacers your carb out by 1/4". Stack more to increase distance for performance tuning. Gaskets or bolts not included. UNPAINTED

Wide Frame PTO Clutch Setup Tool

$4 / ea.

    For the Wide Frame Front PTO's. Made to exact specs as the original, but out of .062" thick stainless steel.

Narrow Frame PTO Clutch Setup Tool

$4 / ea.

    For the Narrow Frame Front PTO's. Made to exact specs as the original, but out of .062" thick stainless steel.

Cub Cadet 3 Pin Clutch Driver

$60 / ea.

    This is a new reproduction 3 pin clutch driver for manual transmission Cub Cadets. Heavy duty .179 backer with machined hub and oilite iron bronze bushing. Pins are adjustable and replaceable.

Narrow Frame Clutch Lever

$55 / ea.

    Cub Cadet Clutch Lever Hanger Assembly. Fits 86, 108, 128, 800, 1000, 1200 Also 1250, 1450, 1650 Equipped with a Hydrostatic Disconnect Attachment. Reproduction of the original unit. Unpainted Replaces Cub Cadet PN IH-547629-R1

Wide Frame Drive Shaft -Full Length

$55 / ea.

    IH PN/ IH-545511-R1 Fits 109 129 149 169 Measures 17.50" from face of mounting bracket to middle of pin hole. Includes pin - not installed.

Narrow Frame Drive Shaft -Full Length

$55 / ea.

    IH PN/ IH-397373-R2 Fits 105, 107, 123, 125, 127, 147 Measures 16.50" from face of mounting bracket to middle of pin hole. Includes pin - not installed.

Drive Shaft -Full Length

$50 / ea.

    IH PN/ IH-385982-R91 Fits 70, 71, 72, 73, 100, 102, 104, 106, 124, 126 without creeper. Can be used with above and creeper gears but must be shortened at the cut line. Measures 18.20" from end to end. Measures 16.70" between farthest 2 holes. Included cut off line for future creeper installation.

Drive Shaft -Full Length

$50 / ea.

    IH PN/ IH-545492-R91 Fits Fits 86 108 128 without creeper. Can be used with above and creeper gears but must be shortened at the cut line. Measures 19.20" from end to end. Measures 17.70" between farthest 2 holes. Included cut off line for future creeper installation.

Drive Shaft - Original - Without Creeper

$55 / ea.

    IH PN/ IH- 376255-R11 Fits Fits Cub Cadet Original without creeper. not painted Measures 21.00" from end to end.

Drive Shaft - Original - With Creeper

$55 / ea.

    IH PN/ IH- 376255-R11 Fits Fits Cub Cadet Original with creeper. not painted Measures 16.88" from end to end.

Drive Shaft - Blank

$35 / ea.

    If you need to make a driveshaft with a custom configuration - then this blank will get you what you need. 5/8" dia. CR Steel with the T-Tab welded to the end. There are no holes drilled in it. Measures 21.00" from end to end.

Drive Shaft Material

$30 / ea.

    If you need to make a driveshaft with a custom configuration - then this blank will get you what you need. 5/8" dia. CR Steel. There are no holes drilled in it . Measures 24.00" from end to end.

TITLE HERE

$ / ea.

    DESCRIPTION

TITLE HERE

$ / ea.

    DESCRIPTION